This can be caused by a variety of problems, such as PCI IRQ routing errors, I/O APIC problems or conflicts with other devices sharing the IRQ (or their drivers).

If possible, configure your system such that your graphics card does not share its IRQ with other devices (try moving the graphics card to another slot if applicable, unload/disable the driver(s) for the device(s) sharing the card's IRQ, or remove/disable the device(s)).

Depending on the nature of the problem, one of (or a combination of) these kernel parameters might also help:

An edge-triggered interrupt means that the kernel has programmed the interrupt as edge-triggered rather than level-triggered in the Advanced Programmable Interrupt Controller (APIC). Edge-triggered interrupts are not intended to be used for sharing an interrupt line between multiple devices; level-triggered interrupts are the intended trigger for such usage. When using edge-triggered interrupts, it is common for device drivers using that interrupt line to stop receiving interrupts. This would appear to the end user as those devices no longer working, and potentially as a full system hang. These problems tend to be more common when multiple devices are sharing that interrupt line.

This occurs when ACPI is not used to program interrupt routing in the APIC. This often occurs on 2.4 Linux kernels, which do not fully support ACPI, or 2.6 kernels when ACPI is disabled or fails to initialize. In these cases, the Linux kernel falls back to tables provided by the system BIOS. In some cases the system BIOS assumes ACPI will be used for routing interrupts and configures these tables to incorrectly label all interrupts as edge-triggered. The current interrupt configuration can be found in /proc/interrupts.

Available workarounds include: updating to a newer system BIOS, trying a 2.6 kernel with ACPI enabled, or passing the 'noapic' option to the kernel to force interrupt routing through the traditional Programmable Interrupt Controller (PIC). Newer kernels also provide an interrupt polling mechanism to attempt to work around this problem. This mechanism can be enabled by passing the 'irqpoll' option to the kernel.

Currently, the NVIDIA driver will attempt to detect edge triggered interrupts and X will purposely fail to start (to avoid stability issues). This behavior can be overridden by setting the "NVreg_RMEdgeIntrCheck" NVIDIA Linux kernel module parameter. This parameter defaults to "1", which enables the edge triggered interrupt detection. Set this parameter to "0" to disable this detection.

If X starts but you have trouble with OpenGL, you most likely have a problem with other libraries in the way, or there are stale symlinks. See Chapter 5, Installed Components for details. Sometimes, all it takes is to rerun ldconfig.

You should also check that the correct extensions are present;

    % xdpyinfo

should show the “GLX” and “NV-GLX” extensions present. If these two extensions are not present, then there is most likely a problem loading the glx module, or it is unable to implicitly load GLcore. Check your X config file and make sure that you are loading glx (see Chapter 6, Configuring X for the NVIDIA Driver). If your X config file is correct, then check the X log file for warnings/errors pertaining to GLX. Also check that all of the necessary symlinks are in place (refer to Chapter 5, Installed Components).

This problem occurs with DDC and "blue line" stereo glasses, that get the stereo signal from one video port of the graphics card. When a X screen does not display any stereo drawable the stereo signal is disabled on the associated video port.

Forcing stereo flipping allows the stereo glasses to shutter continuously. This can be done by enabling the OpenGL control "Force Stereo Flipping" in nvidia-settings, or by setting the X configuration option "ForceStereoFlipping" to "1".

There are two cases where this may occur. If the displays are attached to the same GPU, and one of them is out of sync with the stereo glasses, you will need to reconfigure your monitors to drive identical mode timings; see Chapter 19, Programming Modes for details.

If the displays are attached to different GPUs, the only way to synchronize stereo across the displays is with a G-Sync device, which is only supported by certain Quadro cards. See Chapter 26, Frame Lock and Genlock for details. This applies to seperate GPUs on seperate cards as well as seperate GPUs on the same card, such as Quadro FX 4500 X2. Note that the Quadro FX 4500 X2 only provides a single DIN connector for stereo, tied to the bottommost GPU. In order to synchronize onboard stereo on the other GPU you must use a G-Sync device.

The kernel interface layer of the NVIDIA kernel module must be compiled specifically for the configuration and version of your kernel. If you upgrade your kernel, then the simplest solution is to reinstall the driver.

ADVANCED: You can install the NVIDIA kernel module for a non running kernel (for example: in the situation where you just built and installed a new kernel, but have not rebooted yet) with a command line such as this:

    # sh NVIDIA-Linux-x86_64-100.14.06-pkg1.run --kernel-name='KERNEL_NAME'

Where 'KERNEL_NAME' is what uname -r would report if the target kernel were running.

The X driver will abort with this error message if the NVIDIA kernel module fails to load. If you receive this error, you should check the output of dmesg for kernel error messages and/or attempt to load the kernel module explicitly with modprobe nvidia. If unresolved symbols are reported, then the kernel module was most likely built against a Linux kernel source tree (or kernel headers) for a kernel revision or configuration that doesn't match the running kernel.

You can specify the location of the kernel source tree (or headers) when you install the NVIDIA driver using the --kernel-source-path command line option (see sh NVIDIA-Linux-x86_64-100.14.06-pkg1.run --advanced-options for details).

Old versions of the module-init-tools include modprobe binaries that report an error when instructed to load a module that's already loaded into the kernel. Please upgrade your module-init-tools if you receive an error message to this effect.

The X server reads /proc/sys/kernel/modprobe to determine the path to the modprobe utility and falls back to /sbin/modprobe if the file doesn't exist. Please make sure that this path is valid and refers to a modprobe binary compatible with the Linux kernel running on your system.

The "LoadKernelModule" X driver option can be used to change the default behavior and disable kernel module auto-loading.

You need to install the source for the Linux kernel. In most situations you can fix this problem by installing the kernel-source or kernel-devel package for your distribution

The dynamic loader on your system has a bug which will cause applications linked with pthreads, and that dlopen() libGL multiple times, to crash. This bug is present in older versions of the dynamic loader. Distributions that shipped with this loader include but are not limited to Red Hat Linux 6.2 and Mandrake Linux 7.1. Version 2.2 and later of the dynamic loader are known to work properly. If the crashing application is single threaded then setting the environment variable __GL_SINGLE_THREADED to 1 will prevent the crash. In the bash shell you would enter:

    % export __GL_SINGLE_THREADED=1

and in csh and derivatives use:

    % setenv __GL_SINGLE_THREADED 1

Previous releases of the NVIDIA Accelerated Linux Graphics Driver attempted to work around this problem. Unfortunately, the workaround caused problems with other applications and was removed after version 1.0-1541.

You are probably experiencing a problem described above. Please check the text output for the “WARNING” message described in the previous hint. Setting __GL_SINGLE_THREADED to 1 as will fix the problem.

These problems are generally caused by the build using the wrong kernel header files (i.e. header files for a different kernel version than the one you are running). The convention used to be that kernel header files should be stored in /usr/include/linux/, but that is deprecated in favor of /lib/modules/RELEASE/build/include (where RELEASE is the result of uname -r. The nvidia-installer should be able to determine the location on your system; however, if you encounter a problem you can force the build to use certain header files by using the --kernel-include-dir option. For this to work you will of course need the appropriate kernel header files installed on your system. Consult the documentation that came with your distribution; some distributions do not install the kernel header files by default, or they install headers that do not coincide properly with the kernel you are running.

Heretic II installs, by default, a symlink called libGL.so in the application directory. You can remove or rename this symlink, since the system will then find the default libGL.so (which our drivers install in /usr/lib). From within Heretic II you can then set your render mode to OpenGL in the video menu. There is also a patch available to Heretic II from lokigames at: http://www.lokigames.com/products/heretic2/updates.php3/

Using both rivafb and the NVIDIA kernel module at the same time is currently broken. In general, using two independent software drivers to drive the same piece of hardware is a bad idea.

You should compile the NVIDIA kernel module with the same compiler version that was used to compile your kernel. Some Linux kernel data structures are dependent on the version of gcc used to compile it; for example, in include/linux/spinlock.h:

        ...
        * Most gcc versions have a nasty bug with empty initializers.
        */
        #if (__GNUC__ > 2)
          typedef struct { } rwlock_t;
          #define RW_LOCK_UNLOCKED (rwlock_t) { }
        #else
          typedef struct { int gcc_is_buggy; } rwlock_t;
          #define RW_LOCK_UNLOCKED (rwlock_t) { 0 }
        #endif

If the kernel is compiled with gcc 2.x, but gcc 3.x is used when the kernel interface is compiled (or vice versa), the size of rwlock_t will vary, and things like ioremap will fail. To check what version of gcc was used to compile your kernel, you can examine the output of:

    % cat /proc/version

To check what version of gcc is currently in your $PATH, you can examine the output of:

    % gcc -v

This is one of the possible consequences of compiling the NVIDIA kernel interface with a different gcc version than used to compile the Linux kernel (see above).

Conflicting libraries may have been installed by your distribution's update utility; see Chapter 5, Installed Components for details on how to diagnose this.

Unresolved symbols are most often caused by a mismatch between your kernel sources and your running kernel. They must match for the NVIDIA kernel module to build correctly. Make sure your kernel sources are installed and configured to match your running kernel.

The kernel header files Red Hat Linux distributes for Red Hat Linux 7.3 2.4.18-3bigmem kernel are misconfigured. NVIDIA's precompiled kernel module for this kernel can be loaded, but if you want to compile the NVIDIA kernel interface files yourself for this kernel, then you will need to perform the following:

    # cd /lib/modules/`uname -r`/build/
    # make mrproper
    # cp configs/kernel-2.4.18-i686-bigmem.config .config
    # make oldconfig dep

Note: Red Hat Linux ships kernel header files that are simultaneously configured for ALL of their kernels for a particular distribution version. A header file generated at boot time sets up a few parameters that select the correct configuration. Rebuilding the kernel headers with the above commands will create header files suitable for the Red Hat Linux 7.3 2.4.18-3bigmem kernel configuration only, thus making the header files for the other configurations unusable.

If your kernel is making use of the -rmap VM, the system may be leaking memory due to a memory management optimization introduced in -rmap14a. The -rmap VM has been adopted by several popular distributions, the memory leak is known to be present in some of the distribution kernels; it has been fixed in -rmap15e.

If you suspect that your system is affected, try upgrading your kernel or contact your distribution's vendor for assistance.

Some versions of the glibc package shipped by Red Hat that support TLS do not properly handle using dlopen() to access shared libraries which use some TLS models. This problem is exhibited, for example, when Quake3 Area dlopen()'s NVIDIA's libGL library. Please obtain at least glibc-2.3.2-11.9 which is available as an update from Red Hat.

Most distribution-provided configuration applets are not aware of the NVIDIA accelerated driver, and consequently will not update themselves when you install the driver. Your driver, if it has been installed properly, should function fine.

These games close and reopen the NVIDIA OpenGL driver (via dlopen()/dlclose()) when settings are changed. On some versions of glibc (such as the one shipped with Red Hat Linux 9), there is a bug that leaks static TLS entries. This glibc bug causes subsequent re-loadings of the OpenGL driver to fail. This is fixed in more recent versions of glibc; see Red Hat bug #89692: https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=89692

The NVIDIA OpenGL driver and the NVIDIA X driver require shared memory to communicate; you must have CONFIG_SYSVIPC enabled in your kernel.

The installer detects the presence of an X server by checking for X's lock files: /tmp/.Xn-lock, where 'n' is the number of the X Display (the installer checks for X Displays 0-7). If you have exited X, but one of these files has been left behind, then you will need to manually delete the lock file. Do not remove this file if X is still running!

Your stability problems may be AGP-related. See Chapter 12, Configuring AGP for details.

The application is probably using a different library that still remains on your system, rather than the NVIDIA supplied OpenGL library. See Chapter 5, Installed Components for details.

Quake2 requires some minor setup to get it going. First, in the Quake2 directory, the install creates a symlink called libGL.so that points at libMesaGL.so. This symlink should be removed or renamed. Second, in order to run Quake2 in OpenGL mode, you must type

    % quake2 +set vid_ref glx +set gl_driver libGL.so

Quake2 does not seem to support any kind of full-screen mode, but you can run your X server at the same resolution as Quake2 to emulate full-screen mode.

Integrated graphics have more strict memory bandwidth limitations that limit the resolution and refresh rate of the modes you request. To work around this, you can reduce the maximum refresh rate by lowering the upper value of the VertRefresh range in the Monitor section of your X config file. Though not recommended, you can disable the memory bandwidth test with the NoBandWidthTest X config file option.

Most of the X startup delay problems we have found are caused by incorrect data in video BIOSes about what display devices are possibly connected or what i2c port should be used for detection. You can work around these problems with the X config option IgnoreDisplayDevices (see the description in Appendix B, X Config Options).

Incorrectly sized fonts are generally caused by incorrect DPI (Dots Per Inch) information. You can check what X thinks the physical size of your monitor is, by running:

 % xdpyinfo | grep dimensions

This will report the size in pixels, and in millimeters.

If these numbers are wrong, you can correct them by modifying the X server's DPI setting. See Appendix E, Dots Per Inch for details.

There are some known timing and signal integrity issues on ALi chipsets. The following tips may help stabilize problematic ALI systems:

The installation of GNOME provided in operating systems such as Red Hat Enterprise Linux 4 and Solaris 10 Update 2 contain several competing interfaces for specifying resolution:

    'System Settings' -> 'Display'

which will update the X configuration file, and

    'Applications' -> 'Preferences' -> 'Screen Resolution'

which will update the per-user screen resolution using the XRandR extension. Your desktop resolution will be limited to the smaller of the two settings. Be sure to check the setting of each.

The NVIDIA X driver uses the X Int10 module to save and restore console state on TV out, and will not be able to restore the console correctly if it cannot use the Int10 module. If you have built the X server yourself, please be sure you have built the Int10 module. If you are using a build of the X server provided by your operating system and are missing the Int10 module, contact your operating system distributor.