These are 1.2 MB bootdisk images for Slackware Linux 8.0.0. These disks use Linux kernel version 2.2.19. You'll need one of these to get Linux started on your system so that you can install it. Because of the possibility of collisions between the various Linux drivers, several bootkernel disks have been provided. You should use the one with the least drivers possible to maximize your chances of success. All of these disks support UMSDOS. You will be using the bootdisk to load and start a rootdisk. See the /rootdsks directory for these. (BUT, be sure to read the important information below!) A bootdisk is created by writing the image to a formatted floppy disk with RAWRITE.EXE under DOS. For example, to use RAWRITE.EXE to create the bare.i bootdisk you'd put a formatted disk in your floppy drive and issue the following command: C:\> RAWRITE BARE.I A: Tip: If you have no idea which bootdisk to use, start with "bare.i". This is the correct disk to use for most systems with IDE peripherals. Note: If you need to support an unusual hardware combination during the installation (for example, you want to do an NFS installation using a SCSI card and network card that aren't both in the scsinet.s image), then you may need to use a generic bootdisk like "bare.i" and load the additional drivers as kernel modules before running "setup". See the README files in the ../modules directory for details on how to do this. -------------------------------------------------------------------------------- ...and now some important information (i.e. the bad news ;) for people with systems that use a 1.2 megabyte (5 1/4 inch) boot floppy drive: Systems with 1.2 megabyte boot floppy drives are no longer fully supported for installation. (if you can get the system installed, everything will work fine) But, the rootdisks in Slackware no longer fit on 1.2 megabyte floppies. As a result, you'll need to use one of the following workarounds. We will list them in order of most to least recommended: 1. If you have a bootable CD-ROM drive, some Slackware CD-ROMs (for example, the ones supplied by Walnut Creek CDROM) can be directly booted. If you have this capability, you won't need to use any installation floppies. 2. Don't use installation floppies at all. Instead, start the installation process from DOS. To do this, install loadlin (lodlin16.zip in the kernels directory) on your DOS drive, and put these files in the same directory: A kernel, such as: \kernels\bare.i\zimage A rootdisk, such as: \rootdsks\color.gz Then, run this command in DOS to start the installation process: loadlin zimage root=/dev/ram initrd=color.gz load_ramdisk=1 rw If you aren't sure which kernel from the \kernels directory to use (there are over 50 of them to choose from), you can take a look at the README file in the \bootdsks.144 directory. The descriptions of those bootdisks are equally applicable to the raw kernels found in \kernels. A good starting choice is /kernels/bare.i/zImage, which provides support for IDE based machines. 3. If you happen to have a 1.44 megabyte SECOND floppy drive (B:) you can boot one of the bootdisks in this directory, and load the rootdisk from your second floppy drive with this command on the boot prompt: ramdisk root=/dev/fd1 4. If you're thinking about using a UMSDOS installation (this puts Linux on your DOS drive in a \LINUX directory), consider using the ZipSlack installation process to get started. Instructions are in the \zipslack directory. 5. Install a 1.44 megabyte floppy drive as your first floppy drive. (and while you're at it, add some more memory ;^) 6. You can try using one of the unsupported rootdisks in \rootdsks\obsolete that will fit on a 1.2 megabyte floppy disk. -------------------------------------------------------------------------------- Here's a description of the 1.2 MB bootdisks: bare.i This is the disk to use for installation on most IDE based PCs. It includes support for IDE/ATAPI CD-ROM drives. scsi.s A generic SCSI bootdisk, with support for most SCSI controllers that work under Linux. --------------------------------------------------------------------------------- IMPORTANT HELPFUL HINTS: (AND WHAT TO DO IF THE INSTALLED SYSTEM WON'T BOOT) The kernels provided with the Slackware A series (ide and scsi) are reasonably generic to maximize the chances that your system will boot after installation. However, you should compile a custom kernel after installing, selecting only the drivers your system requires. This will offer optimal performance. You'll need to recompile your kernel to enable support for non-SCSI CD-ROM drives, bus-mice, sound cards, and many other pieces of hardware. The drivers could not be included with the pre-compiled kernels because they cause system hangs and other compatiblity problems for people that don't have the hardware installed. On a similar note, any time you use one kernel to install, and a different kernel the first time the installed system is started, you run the risk that the second kernel won't be compatible for some reason. If your system fails to reboot after installation, you'll have to compile a custom kernel for your hardware. Follow these steps: 0. If you haven't installed the C compiler and kernel source, do that. 1. Use the bootdisk you installed with to start your machine. At the LILO prompt, enter: mount root=/dev/hda1 ^^^^^^^^^ Or whatever your root Linux partition is. Ignore any error messages as the system starts up. 2. Log in as root, and recompile the kernel with these steps. (Comments will be placed in parenthesis) cd /usr/src/linux make config (Choose your drivers. Repeat this step until you are satisfied with your choices) If you are using LILO, this will build and install the new kernel: make dep ; make clean ; make zlilo rdev -R /vmlinuz 1 If you are using a bootdisk, these commands will build the kernel and create a new bootdisk for your machine: make dep ; make clean ; make zImage rdev -R zImage 1 (If you use UMSDOS for your root partition, use 'rdev -R zImage 0' instead) rdev -v zImage -1 rdev zImage /dev/hda1 (replace /dev/hda1 with the name of your root Linux partition) (Now, put a disk into your floppy drive to be made into the new bootdisk:) fdformat /dev/fd0u1440 cat zImage > /dev/fd0 That should do it! You should now have a Linux kernel that can make full use of all supported hardware installed in your machine. Reboot and try it out. Good luck! --- Patrick Volkerding volkerdi@slackware.com PS - Bug reports welcome. Requests for help may be answered if time permits. I've been happy to do this in the past, but lately I've had both a lot more work to do and a lot more mail to deal with. It's just not as possible to keep up with my mail as it once was.